I have a Talon Wifi card in a FX30s running Legato 21. Does the fx30_catm_4_1_0 release come included with support for this card. I cannot see any of the ti drivers. If I need to compile , are there any instructions ?

other user can make it work, you can check with him here: [image] Wifi exp board on legato21 (R15) For the FX30 connected WIFI connection through wlan0 with IP 192.168.1.11, can the FX30 browse internet? For the client connected on eth0 has 192.168.13.10 (static), can it…

So my FX30 is missing hostap* too I also tried with fx30_catm_4_1_0 images like you did in that thread (you tried an older version). But even after installing 9999999_9907618_SWI9X06Y_02.36.08.02_00_GENERIC_001.077_000-full.spk I cannot find hostap Is the solution to rebuild yocto ? And we do n…

I think you can try that to include hostapd first.

ok, since /bin is read-only is there a simple way to only copy hostapd and make it appear in /bin or should I have to re-generate the .SPK and download again ? I have hostapd from my previous yocto build but it did not get included due to “REMOVE” in the bitbake recipe.

Here is an example to overlay on read only file system. [image] Create folders inside /mnt (w/o editing sierra_git.bb) Legato Linux distribution (Yocto project) I remember i can overlay on read only file system. For example, mkdir /tmp/tmp_usr_lib;mkdir /tmp/tmp_usr_lib…

thanks. So I did these 2 things (this may help others) Overlay /bin and copied hostapd to /bin on the FX30 Enabled wifi client modified tiwifi and removed all the gpioexp stuff from there (it was giving me i2c errors) used wifi client to setup the connection This seemed to work one time BUT after…

I can confirm this issue is linked with wifiService. To reproduce Remove gpioenable stuff from tiwifi and allow the script to run fully Reboot system or simply restart wifiService Kernel will throw panic

[ 188.264965] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11) [ 188.321788] wlcore: loaded [ 189.580843] wlcore: PHY firmware version: Rev 8.2.0.0.240 [ 189.638200] wlcore: firmware booted (Rev 8.9.0.0.76) [ 189.661852] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 191.013706] …

@sunil.somarajan Does this relate to the hostapd in R14? @ccu , do you see such issue?

I am using R15 (hostapd from R15 yocto build). this is related to WifiService. So I really dont need wifiService or the wifi client tool. How can I autostart wlan0 using wpa_supplicant.conf and obtain an IP address ?

R15 Legato_21 and Talon Wifi IOT card

Uncategorized

jyijyi January 20, 2023, 5:33am 2

other user can make it work, you can check with him here:

Topic		Replies	Views
Wifi exp board on legato21 (R15) Uncategorized	46	880	January 6, 2023
FX30s LTE [WP7702] WIFI access with Talon IOT card Uncategorized	2	663	April 23, 2020
Debugging IoT wifi module Legato Linux distribution (Yocto project)	2	1365	September 20, 2017
Issue building legato wifi driver Legato Application Framework	6	1326	January 22, 2018
Got error When Create Access Point with FX30 and IOT card Uncategorized	14	1462	May 2, 2019

R15 Legato_21 and Talon Wifi IOT card

Related topics