Hi, I have a FX30s modem. I have modified the startlegato.sh file in /etc/init.d. This runs normally on many many devices…
However I have one device that is not running the script. Any ideas? Why would it not run that script on start up? It seems to be starting legato but not by running startlegato.sh
I recently downgraded the FW to simulate devices in the field… from R17 to R14 I think it is… in case that might have caused this.
Thanks,
Karl
have you compared the boot up message in UART with good module?
Is it FX30 CAT -1 modem with WP76 module inside?
I remember we should not downgrade from R17 to previous version.
do you see the init script running if upgrading to R17 again?
Hi and thanks for the reply… This is a 3G WP85 module… is the reason for not downgrading explained somewhere so I can understand the issue?
What am I looking for in dmesg output?
oh, i was thinking you were using WP76, then it is not related to the “not downgrading” recommendation
dmesg might not give all the debug message.
i think you should look into the boot up log in UART.
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.2-00096
S - IMAGE_VARIANT_STRING=LAATANAZA
S - OEM_IMAGE_VERSION_STRING=SWI9X06Y_02.36.08.09 c094f4 jenkins 2022/06/24 03:14:00
S - Boot Config, 0x000002e1
B - 1216 - PBL, Start
B - 3720 - bootable_media_detect_entry, Start
B - 4999 - bootable_media_detect_success, Start
B - 5004 - elf_loader_entry, Start
B - 8459 - auth_hash_seg_entry, Start
B - 32205 - auth_hash_seg_exit, Start
B - 83586 - elf_segs_hash_verify_entry, Start
B - 130650 - PBL, End
B - 138927 - SBL1, Start
B - 200842 - pm_device_init, Start
B - 220911 - PM_SET_VAL:Skip
D - 18452 - pm_device_init, Delta
B - 222253 - boot_config_data_table_init, Start
D - 0 - boot_config_data_table_init, Delta - (0 Bytes)
B - 230976 - CDT version:3,Platform ID:8,Major ID:1,Minor ID:0,Subtype:129
B - 237869 - sbl1_ddr_set_params, Start
B - 241712 - Pre_DDR_clock_init, Start
D - 213 - Pre_DDR_clock_init, Delta
D - 0 - sbl1_ddr_set_params, Delta
B - 254400 - pm_driver_init, Start
D - 4483 - pm_driver_init, Delta
B - 260653 - cpr_init, Start
D - 122 - cpr_init, Delta
B - 265319 - cpr_cx_mx_apc_vol_update, Start
D - 91 - cpr_cx_mx_apc_vol_update, Delta
B - 280508 - clock_init, Start
D - 152 - clock_init, Delta
B - 280752 - boot_flash_init, Start
D - 40138 - boot_flash_init, Delta
B - 323910 - boot_flash_swi_ddr_init, Start
D - 29798 - boot_flash_swi_ddr_init, Delta
B - 535305 - Invalid PMIC gpio 3
B - 535366 - Invalid PMIC gpio 3
B - 535397 - Failed to configure/read HW ID minor bit 0
B - 540704 - hw_family:5, hw_type:22, hw_rev:40
B - 549030 - SSMEM init OK
B - 552446 - DEBUG OU: 0000000000000002
B - 552507 - DEBUG OU - setting: 2
B - 555008 - is_memory_dump_allowed (0) in this secure module
B - 560834 - ssmem_get: region 18 not exists
B - 565043 - cannot get SSMEM fwupdate region
B - 585508 - USB non-zero endpoint requirements: 11 in, 6 out
B - 587094 - opening partition 0:SWIFOTA
B - 589382 - error for readpage:0
B - 594872 - DWL-get: ecnt=1 code=0
B - 601887 - API change: date not generated by cwe_header_init
B - 609329 - Failed to read size: /swinv/item_files/CUST_IM_SWITCH_HIDE
B - 615215 - Failed to read size: /swinv/item_files/FOTA_PARTITION
B - 616405 - Failed to read size: /swinv/item_files/CUST_IM_CONFIG
B - 628727 - flags: u=1 e=1 obmsk=c,0
B - 638151 - ssmem_release: region 20 not exists
B - 638212 - ssmem_get: region 20 not exists
B - 642269 - Image Load, Start
D - 95556 - QSEE Image Loaded, Delta - (490996 Bytes)
D - 213 - boot_pm_post_tz_device_init, Delta
B - 742248 - sbl1_efs_handle_cookies, Start
D - 0 - sbl1_efs_handle_cookies, Delta
B - 750239 - DEVCFG ELF verification failure
B - 753777 - Image Load, Start
D - 30 - SEC Image Loaded, Delta - (0 Bytes)
B - 761463 - Image Load, Start
D - 55113 - RPM Image Loaded, Delta - (151248 Bytes)
B - 817278 - Image Load, Start
B - 819596 - Auth disabled for image 9
B - 864888 - ssmem_get: region 20 not exists
D - 47671 - APPSBL Image Loaded, Delta - (440540 Bytes)
B - 868152 - QSEE Execution, Start
D - 915 - QSEE Execution, Delta
B - 874892 - SBL1, End
D - 738253 - SBL1, Delta
S - Throughput, 8000 KB/s (1261792 Bytes, 142761 us)
S - DDR Frequency, 240 MHz
Android Bootloader - UART_DM Initialized!!!
[10] Qseecom Init Done in Appsbl version is 0x405000
[10] secure app region addr=0x87900000 size=0x280000[20] TZ App region notif returned with status:0 addr:87900000 size:2621440
[20] TZ App log region register returned with status:0 addr:82685000 size:4096
[30] Qseecom TZ Init Done in Appsbl
[30] QUP: I2C status flags :0x1363c8
[40] QUP: I2C status flags :0x11163c8
[40] I2C slave addr:0x50 not connected
[40] Board: MangOH Red
[50] ERROR: No devinfo partition found
[50] Neither 'config' nor 'frp' partition found
[50] ERROR: No misc partition found
[1820] boot_verifier: Error while reading signature length.
[1830] SSMEM init OK[1830] ssmem_get: region 20 not exists[1830] SWI: auth failed, OEM auth disabled
[1930] ERROR: No devinfo partition found
[1940] DEBUG: cmdline has root=
[2000] Channel alloc freed
[ 0.077788] msm_watchdog b017000.qcom,wdt: Couldn't get memory for dump
[ 0.078898] unable to find DT imem DLOAD mode node
[ 0.079376] unable to find DT imem EDLOAD mode node
[ 0.079814] unable to find DT imem dload-type node
[ 0.080194] Failed to disable secure wdog debug: -4
[ 0.094095] mdm9607-pinctrl 1000000.pinctrl: invalid resource
[ 0.095048] SWI ssmem_framework_init: SSMEM init OK
[ 0.095119] mdm9607-pinctrl 1000000.pinctrl: gpio-bit-map = 36
[ 0.172544] running cpufreq for CPU0 without cooling dev: -38
[ 0.206749] msm_bus_fabric_init_driver
[ 0.557604] qcom-sps-dma 7884000.qcom,sps-dma: dma_async_device_register: device has no channels!
[ 0.663357] msm_serial 78b0000.serial: Disabled
[ 0.672594] mdm9607-pinctrl 1000000.pinctrl: pin GPIO_12 already requested by 78af000.serial; cannot claim for 78af000.uart
[ 0.676440] mdm9607-pinctrl 1000000.pinctrl: pin-12 (78af000.uart) status -22
[ 0.687369] mdm9607-pinctrl 1000000.pinctrl: could not request pin 12 (GPIO_12) from group gpio12 on device 1000000.pinctrl
[ 0.694620] msm_serial_hs 78af000.uart: Error applying setting, reverse things back
[ 0.706084] uart_tx_gpio is not available
[ 0.713293] uart_rx_gpio is not available
[ 0.717404] uart_cts_gpio is not available
[ 0.721439] uart_rfr_gpio is not available
[ 0.725957] sps: BAM device 0x07884000 is not registered yet.
[ 0.740689] diag: diag_pcie_register: failed registering pcie channels
[ 0.740720] diag: MUX: unable to register pcie operations for proc: 0, err: -22
[ 0.746110] diag: MUX: unable to register PCIe operations, continuing with USB registrations for proc: 0, err: -22
[ 0.778986] QSEECOM: qseecom_probe: Failed to get QSEE version info -19
[ 0.784819] sps: BAM device 0x07984000 is not registered yet.
[ 0.810366] msm_otg 78d9000.usb: usb_add_phy failed
[ 0.841984] msm_hsic_host 7c00000.hsic_host: Probe success
[ 0.915386] pca953x 4-0020: failed reading register
[ 0.915984] pca953x 4-0022: failed reading register
[ 0.954615] msm_otg 78d9000.usb: Could not get usb power_supply
[ 0.954699] msm_otg 78d9000.usb: Could not get usb power_supply
[ 0.962228] Error registering TZ zone:-19 for dt_ch:52
[ 0.986595] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30-NETWORK_LED_RED". Unable to decode.
[ 0.986643] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30-NETWORK_LED_GRN". Unable to decode.
[ 0.994817] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30-SIGNAL_LED_RED". Unable to decode.
[ 1.003502] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30-SIGNAL_LED_GRN". Unable to decode.
[ 1.012255] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30-USER_LED_RED". Unable to decode.
[ 1.021068] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30-USER_LED_GRN". Unable to decode.
[ 1.029358] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30-POWER_LED_RED_N". Unable to decode.
[ 1.038124] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30-POWER_LED_GRN". Unable to decode.
[ 1.046937] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30-POWER_LED_MUX". Unable to decode.
[ 1.055439] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30-GPS_BIAS_EN". Unable to decode.
[ 1.064310] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30-IO_PULLUP_EN2". Unable to decode.
[ 1.072936] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30-IO_PULLUP_EN3". Unable to decode.
[ 1.082407] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30-ETH_DISABLE_N". Unable to decode.
[ 1.091189] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30-DIGITAL_OUTPUT3". Unable to decode.
[ 1.098796] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30-IO_PULLUP_EN1". Unable to decode.
[ 1.107793] msm_otg 78d9000.usb: Could not get usb power_supply
[ 1.116223] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30-POWER_HOLD". Unable to decode.
[ 1.122101] msm_otg 78d9000.usb: Could not get usb power_supply
[ 1.131179] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-NETWORK_LED_RED". Unable to decode.
[ 1.136391] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-NETWORK_LED_GRN". Unable to decode.
[ 1.145509] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-SIGNAL_LED_RED". Unable to decode.
[ 1.154428] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-SIGNAL_LED_GRN". Unable to decode.
[ 1.163471] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-USER_LED_RED". Unable to decode.
[ 1.172199] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-USER_LED_GRN". Unable to decode.
[ 1.180707] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-POWER_LED_RED_N". Unable to decode.
[ 1.189340] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-POWER_LED_GRN". Unable to decode.
[ 1.198418] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-POWER_LED_MUX". Unable to decode.
[ 1.207351] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-GPS_BIAS_EN". Unable to decode.
[ 1.216116] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-IO_PULLUP_EN2". Unable to decode.
[ 1.224587] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-IO_PULLUP_EN3". Unable to decode.
[ 1.233561] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-GPIO55". Unable to decode.
[ 1.242276] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-DIGITAL_OUTPUT3". Unable to decode.
[ 1.250327] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-IO_PULLUP_EN1". Unable to decode.
[ 1.259136] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-POWER_HOLD". Unable to decode.
[ 1.268157] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-RS485_OUT_EN". Unable to decode.
[ 1.276610] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-RS485_IN_EN_N". Unable to decode.
[ 1.285106] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-RS485_POL_N". Unable to decode.
[ 1.294599] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-GPIO64". Unable to decode.
[ 1.302749] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-GPIO65". Unable to decode.
[ 1.310843] sierra_gpio soc:sierra_gpio: Skipping "alias-FX30S-GPIO66". Unable to decode.
[ 1.320903] calculate_residency: residency < 0 for LPM
[ 1.327033] parse_cpu_levels: idx 1 420
[ 1.332312] calculate_residency: residency < 0 for LPM
[ 1.335819] parse_cpu_levels: idx 2 500
[ 1.341015] parse_cpu_levels: idx 2 3040
ima: setting up IMA subsystem...
ima: feature not supported
The proc node does not exist
mount root fs from partition (rootfs|system)
UBI device number 0, total 120 LEBs (30474240 bytes, 29.0 MiB), available 0 LEBs (0 bytes), LEB size 253952 bytes (248.0 KiB)
[ 1.519225] SWI ssmem_alloc_entry_get: ssmem region 20 not allocated
[ 1.519257] SWI ssmem_get: ssmem_get: region 20 not exists
[ 1.524858] SWI ssmem_dev_ioctl: region 20 get failed, ver 100
dm-verity key not installed, authentication disabled
Non-Secure version.
rootfs: dev '/dev/ubiblock0_0' 'squashfs'
mount /dev/mapper/rt
rootfs: mounting took 0ms
rcS: Executing mount_essential_fs...
rcS: Executing simple_network...
rcS: Executing check_recovery...
rcS: Executing run_S_scripts...
S02mount_early: Executing mount_early_pseudo...
S02mount_early: Mounting SMACK security pseudo fs...
S02mount_early: Executing mount_early_other...
S02mount_early: Executing mount_early_create_dirs...
S02mount_early: Executing mount_early_set_timezone...
S02mount_early: Using timezone Universal...
S02mount_early: Executing yaffs2_kern_supported_init...
S02mount_early: Executing mount_early_user_start...
S02mount_early: RO rootfs fudge allowed.
S02mount_early: User is forcing userapp file system to be ubifs.
S02mount_early: Trying to mount UBIFS on /mnt/flash using [usrquota,grpquota,rw] mount options...
UBI device number 3, total 524 LEBs (133070848 bytes, 126.9 MiB), available 5 LEBs (1269760 bytes, 1.2 MiB), LEB size 253952 bytes (248.0 KiB)
[ 5.804481] UBIFS error (ubi3:0 pid 314): ubifs_parse_options.constprop.0: unrecognized mount option "usrquota" or missing value
mount: mounting /dev/ubi3_0 on /mnt/flash failed: Invalid argument
S02mount_early: Unable to mount /dev/ubiblock3_0 onto /mnt/flash.
S02mount_early: Trying to mount UBIFS on /mnt/flash using [rw] mount options...
UBI device number 3, total 524 LEBs (133070848 bytes, 126.9 MiB), available 5 LEBs (1269760 bytes, 1.2 MiB), LEB size 253952 bytes (248.0 KiB)
S02mount_early: UBIFS volume successfully mounted on /mnt/flash
S02mount_early: Executing mount_early_legato_start...
mount Legato from partition lefwkro
UBI device number 2, total 35 LEBs (8888320 bytes, 8.4 MiB), available 0 LEBs (0 bytes), LEB size 253952 bytes (248.0 KiB)
[ 6.810773] SWI ssmem_alloc_entry_get: ssmem region 20 not allocated
[ 6.810805] SWI ssmem_get: ssmem_get: region 20 not exists
[ 6.816194] SWI ssmem_dev_ioctl: region 20 get failed, ver 100
dm-verity key not installed, authentication disabled
Non-Secure version.
S02mount_early: SQUASHFS successfully mounted on /mnt/legato
S02mount_early: Executing mount_early_userrw_start...
S02mount_early: Mounting swirw file system as UBIFS
S02mount_early: Trying to mount UBIFS on /mnt/userrw using [usrquota,grpquota,rw] mount options...
UBI device number 4, total 100 LEBs (25395200 bytes, 24.2 MiB), available 2 LEBs (507904 bytes, 496.0 KiB), LEB size 253952 bytes (248.0 KiB)
[ 8.084763] UBIFS error (ubi4:0 pid 415): ubifs_parse_options.constprop.0: unrecognized mount option "usrquota" or missing value
mount: mounting /dev/ubi4_0 on /mnt/userrw failed: Invalid argument
S02mount_early: Unable to mount /dev/ubiblock4_0 onto /mnt/userrw.
S02mount_early: Trying to mount UBIFS on /mnt/userrw using [rw] mount options...
UBI device number 4, total 100 LEBs (25395200 bytes, 24.2 MiB), available 2 LEBs (507904 bytes, 496.0 KiB), LEB size 253952 bytes (248.0 KiB)
S02mount_early: UBIFS volume successfully mounted on /mnt/userrw
S02mount_early: swirw mounted to /mnt/userrw
S03confighw.sh: Kernel internal entropy pool filler is available, increasing write_wakeup_threshold to 3072
Loading modules: S07mount_unionfs: RO rootfs fudge allowed.
S07mount_unionfs: Overlay over /etc is allowed
S07mount_unionfs: Using timezone [Etc/GMT-8].
[ 9.191341] msm_rpm_flush_requests: Error: more than 24 requests are buffered
Mounting local filesystems...
mount: mounting ubi0:usrfs on /usr failed: No such device
mount modem from partition modem
MTD : Detected block device : /firmware for modem
UBI device number 1, total 128 LEBs (32505856 bytes, 31.0 MiB), available 21 LEBs (5332992 bytes, 5.0 MiB), LEB size 253952 bytes (248.0 KiB)
Initializing random number generator...
starting Busybox Periodic Command Scheduler: crond... done.
crond[659]: crond (busybox 1.31.1) started, log level 8
Configuring network interfaces... done.
Starting syslogd/klogd: done
Switching to composition sierra_dev (1199:68C0)
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCSIFADDR: No such device
[ 15.441812] msm_otg 78d9000.usb: Could not get usb power_supply
[ 15.441846] msm_otg 78d9000.usb: Could not get usb power_supply
SOFTAP_W_DUN: N
Starting diagrebootapp: done
$Starting qcom_time:
starting time-daemon
Starting time_services: done
chmod: /dev/qseecom: No such file or directory
[ 16.370871] qrtr: Modem QMI Readiness RX cmd:0x2 node[0x3]
Starting qrtr-ns: [ 16.406644] qrtr: Modem QMI Readiness TX cmd:0x2 node[0x1]
done
Loading kernel base audio modules...
Done loading kernel base audio modules.
[ 16.573246] diag: In diag_send_peripheral_buffering_mode, buffering flag not set for 0
Starting/Loading audio module: [ 16.693475] scm_call failed with error code -4
[ 16.693509] msm_audio_protect_memory_region: SCM call failed, scm_call_ret -95 tz_resp 0
[ 16.858306] msm_audio_ion_alloc: vaddr = 1c9135e6, size=24
[ 16.859973] msm_audio_ion_alloc: vaddr = 4012dc3f, size=8192
[ 16.863359] msm_audio_ion_alloc: vaddr = f48600e9, size=24
done loading audio_kernel module
Starting mbimd: done
Legato start sequence
start_at_cmux_le: UART1_SERVICE = RS232_FC
start_at_cmux_le: UART1 is NON-AT service, assume DS_MUX daemon over USB
[ 18.961664] mbim_open: USB cable not connected
start_at_cmux_le: Done start_at_cmux_le script.
update-ld-cache: Removing stale mount [/etc/ld.so.conf]...
update-ld-cache: Removing stale mount [/etc/ld.so.cache]...
update-ld-cache: Updating ld.so.cache using [/legato/systems/current/lib]...
update-ld-cache: Updating /etc/ld.so.cache ...
update-ld-cache: Removing stale mount [/etc/ld.so.cache]...
Finished Legato start Sequence
BusyBox v1.31.1 () multi-call binary.
Usage: grep [-HhnlLoqvsriwFE] [-m N] [-A/B/C N] PATTERN/-e PATTERN.../-f FILE [FILE]...
cat: can't open '/sys/class/gpio/v2/gpiochip/ngpio': No such file or directory
sh: write error: Invalid argument
sh: write error: No such file or directory
/etc/rcS.d/S33config_gpios: line 169: can't create /sys/class/gpio/v2/aliases_exported/FX30-NETWORK_LED_RED/direction: nonexistent directory
sh: write error: No such file or directory
/etc/rcS.d/S33config_gpios: line 169: can't create /sys/class/gpio/v2/aliases_exported/FX30-NETWORK_LED_GRN/direction: nonexistent directory
sh: write error: No such file or directory
/etc/rcS.d/S33config_gpios: line 169: can't create /sys/class/gpio/v2/aliases_exported/FX30-SIGNAL_LED_RED/direction: nonexistent directory
sh: write error: No such file or directory
/etc/rcS.d/S33config_gpios: line 169: can't create /sys/class/gpio/v2/aliases_exported/FX30-SIGNAL_LED_GRN/direction: nonexistent directory
sh: write error: No such file or directory
/etc/rcS.d/S33config_gpios: line 169: can't create /sys/class/gpio/v2/aliases_exported/FX30-USER_LED_RED/direction: nonexistent directory
sh: write error: No such file or directory
/etc/rcS.d/S33config_gpios: line 169: can't create /sys/class/gpio/v2/aliases_exported/FX30-USER_LED_GRN/direction: nonexistent directory
sh: write error: No such file or directory
/etc/rcS.d/S33config_gpios: line 169: can't create /sys/class/gpio/v2/aliases_exported/FX30-POWER_LED_RED_N/direction: nonexistent directory
sh: write error: No such file or directory
/etc/rcS.d/S33config_gpios: line 169: can't create /sys/class/gpio/v2/aliases_exported/FX30-POWER_LED_GRN/direction: nonexistent directory
sh: write error: No such file or directory
/etc/rcS.d/S33config_gpios: line 169: can't create /sys/class/gpio/v2/aliases_exported/FX30-GPS_BIAS_EN/direction: nonexistent directory
sh: write error: No such file or directory
/etc/rcS.d/S33config_gpios: line 169: can't create /sys/class/gpio/v2/aliases_exported/FX30-ETH_DISABLE_N/direction: nonexistent directory
sh: write error: No such file or directory
/etc/rcS.d/S33config_gpios: line 169: can't create /sys/class/gpio/v2/aliases_exported/FX30-IO_PULLUP_EN1/direction: nonexistent directory
sh: write error: No such file or directory
/etc/rcS.d/S33config_gpios: line 169: can't create /sys/class/gpio/v2/aliases_exported/FX30-POWER_HOLD/direction: nonexistent directory
sh: write error: No such file or directory
/etc/rcS.d/S33config_gpios: line 174: can't create /sys/class/gpio/v2/aliases_exported/FX30-POWER_LED_MUX/direction: nonexistent directory
sh: write error: No such file or directory
/etc/rcS.d/S33config_gpios: line 174: can't create /sys/class/gpio/v2/aliases_exported/FX30-IO_PULLUP_EN2/direction: nonexistent directory
sh: write error: No such file or directory
/etc/rcS.d/S33config_gpios: line 174: can't create /sys/class/gpio/v2/aliases_exported/FX30-IO_PULLUP_EN3/direction: nonexistent directory
sh: write error: No such file or directory
/etc/rcS.d/S33config_gpios: line 174: can't create /sys/class/gpio/v2/aliases_exported/FX30-DIGITAL_OUTPUT3/direction: nonexistent directory
Starting reboot daemon: done
Starting atreset: done
Starting modem dependent daemons: Load modem done
Starting qmuxd: done
Starting thermal-engine: done
Starting netmgrd: done
Starting powerconfig for mdm9607: sh: write error: Invalid argument
Starting fs-scrub-daemon: done
sysctl: cannot stat /proc/sys/net/ipv4/tcp_syncookies: No such file or directory
net.ipv4.conf.all.log_martians = 1
net.ipv4.conf.all.accept_redirects = 0
net.ipv4.conf.all.accept_source_route = 0
net.ipv4.icmp_echo_ignore_broadcasts = 1
kernel.randomize_va_space = 2
net.ipv4.conf.all.send_redirects = 0
net.ipv4.conf.default.send_redirects = 0
net.ipv4.conf.all.accept_redirects = 0
net.ipv4.conf.default.accept_redirects = 0
net.ipv6.conf.all.accept_redirects = 0
net.ipv6.conf.default.accept_redirects = 0
net.ipv4.conf.all.accept_source_route = 0
net.ipv4.conf.default.accept_source_route = 0
net.ipv6.conf.all.accept_source_route = 0
net.ipv6.conf.default.accept_source_route = 0
net.ipv6.conf.all.accept_ra = 1
net.ipv6.conf.default.accept_ra = 1
net.ipv4.conf.all.log_martians = 1
net.ipv4.conf.default.log_martians = 1
rm: can't remove '/var/log/wtmp': No such file or directory
Starting eMBMs_TunnelingModule: done
Starting qmi_ip: done
[ 30.495554] adm_callback: cmd = 0x10322 returned error = 0x16
[ 30.495586] adm_callback: ADM map error, resuming
[ 30.500603] adm_memory_map_regions: DSP returned error[ADSP_ERR_MAX]
[ 30.504964] adm_map_cal_data: map did not work! cal_type 0 ret -68
[ 30.520319] map_memory: map_cal failed, cal type 10, ret = -19!
[ 30.520353] adm_alloc_cal: cal_utils_alloc_block failed, ret = -19, cal type = 10!
[ 30.525044] call_allocs: alloc failed!
starting DNS forwarder and DHCP server: dnsmasq...
dnsmasq: cannot access /etc/dnsmasq.d/dnsmasq.eth0.conf: No such file or directory
Starting Dropbear SSH server: dropbear.
AT+WDSC?
ERROR
**ERROR: The probation period has already ended. Nothing to do.
run_getty.sh: ttyMSM1 reserved for CONSOLE
Poky (Yocto Project Reference Distro) 3.1.15 fx30 /dev/ttyMSM1
Yes I am as well… but not in this case…
Oh dear, this was a simple problem… The startlegato.sh file did not have execute permissions so was never run…