Hello
I have lost USB ports on WP85 and I don´t know how to activate them again.
I have USB driver installed in my PC and unit had USB ports but after a firmware update or perhaps downloading a Legato application I lost USB port.
Bellow the log
Android Bootloader - UART_DM Initialized!!!
[10] ERROR: No misc partition found
[ 0.000000] Kernel is starting…
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.14.29ltsi-961ca71325_ab5094eade (gsmbuild@CARMD-EV-FRMWR1) (gcc version 4.9.1 (GCC) ) #2 PREEMPT Thu Apr 27 02:17:10 PDT 2017
[ 0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: QCT MSM9615 CDP
[ 0.000000] memory pool 3 (start 4ff00000 size 100000) initialized
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] L310 cache controller enabled
[ 0.000000] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x00540000, Cache size: 262144 B
[ 0.000000] socinfo_init: v7, id=106, ver=3.0, raw_id=1760, raw_ver=1760, hw_plat=0, hw_plat_ver=65536
[ 0.000000] accessory_chip=0, hw_plat_subtype=0, pmic_model=19, pmic_die_revision=3
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 40720
[ 0.000000] Kernel command line: console=ttyHSL0,115200 console=ttyHSL1,115200 fudge_ro_rootfs=true rootfs_ro=true mtdparts=msm_nand:0x00100000@0x051c0000(bootloader),0x01400000(kernel),0x03140000(rootfs),0x02780000(user0),0x08b80000(user1),0x00500000(user2),0x00200000(user3) androidboot.serialno=MDM9615 lkversion=1.3.0_a50272dbb2 androidboot.baseband=msm
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] allocated 507904 bytes of page_cgroup
[ 0.000000] please try ‘cgroup_disable=memory’ option if you don’t want memory cgroups
[ 0.000000] Memory: 150452K/164864K available (6775K kernel code, 632K rwdata, 2260K rodata, 1370K init, 1268K bss, 14412K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0000000 - 0xff000000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xcf800000 ( 248 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc08daf60 (9036 kB)
[ 0.000000] .init : 0xc08db000 - 0xc0a3194c (1371 kB)
[ 0.000000] .data : 0xc0a32000 - 0xc0ad019c ( 633 kB)
[ 0.000000] .bss : 0xc0ad019c - 0xc0c0d4fc (1269 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:681
[ 0.000030] sched_clock: 32 bits at 32kHz, resolution 30520ns, wraps every 65542000541696ns
[ 0.000610] Console: colour dummy device 80x30
[ 0.000701] Calibrating delay loop… 366.18 BogoMIPS (lpj=1830912)
[ 0.060491] pid_max: default: 32768 minimum: 301
[ 0.060949] Security Framework initialized
[ 0.061040] Smack: Initializing.
[ 0.061071] Smack: IPv6 port labeling enabled.
[ 0.061468] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.061498] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.063268] Initializing cgroup subsys debug
[ 0.063329] Initializing cgroup subsys memory
[ 0.063390] Initializing cgroup subsys devices
[ 0.063421] Initializing cgroup subsys freezer
[ 0.063451] Initializing cgroup subsys net_cls
[ 0.063451] Initializing cgroup subsys blkio
[ 0.063543] CPU: Testing write buffer coherency: ok
[ 0.063634] ftrace: allocating 22887 entries in 68 pages
[ 0.145521] Setting up static identity map for 0x40e20580 - 0x40e205d8
[ 0.168899] devtmpfs: initialized
[ 0.178300] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
[ 0.180955] regulator-dummy: no parameters
[ 0.181535] NET: Registered protocol family 16
[ 0.182694] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.182969] AXI: msm_bus_fabric_init_driver(): msm_bus_fabric_init_driver
[ 0.183702] gpio_sync_ri: RI owner is Modem
[ 0.184587] msm_serial_hsl_init: driver initialized
[ 0.185380] cpuidle: using governor ladder
[ 0.185411] cpuidle: using governor menu
[ 0.186143] msm_rpm_init: RPM firmware 3.0.16842958
[ 0.186418] gpio_cf3_low_power_reset_toggle: Setting up LowPower_RESET pin toggle timer
[ 0.186448] unmatched machine ID in register_i2c_devices
[ 0.186479] wl18xx board initialization done
[ 0.186967] 8018_s1: 500 <–> 1150 mV at 1150 mV normal idle
[ 0.187395] 8018_s2: 1225 <–> 1300 mV at 1300 mV normal idle
[ 0.188310] 8018_s3: 1800 mV normal idle
[ 0.188860] 8018_s4: 2100 <–> 2200 mV at 2200 mV normal idle
[ 0.189653] 8018_s5: 1350 mV normal idle
[ 0.190569] 8018_l2: 1800 mV normal idle
[ 0.191454] 8018_l3: 1800 mV normal idle
[ 0.191881] 8018_l4: 3300 mV normal idle
[ 0.192278] 8018_l5: 2850 mV normal idle
[ 0.192675] 8018_l6: 1800 <–> 2850 mV at 2850 mV normal idle
[ 0.193071] 8018_l7: 1850 <–> 1900 mV at 1900 mV normal idle
[ 0.193163] 8018_l7: supplied by 8018_s4
[ 0.193529] 8018_l8: 1200 mV normal idle
[ 0.193651] 8018_l8: supplied by 8018_s3
[ 0.194018] 8018_l9: 750 <–> 1150 mV at 1150 mV normal idle
[ 0.194109] 8018_l9: supplied by 8018_s5
[ 0.194506] 8018_l10: 1050 mV normal idle
[ 0.194597] 8018_l10: supplied by 8018_s5
[ 0.194964] 8018_l11: 1050 mV normal idle
[ 0.195055] 8018_l11: supplied by 8018_s5
[ 0.195544] 8018_l12: 1050 mV normal idle
[ 0.195666] 8018_l12: supplied by 8018_s5
[ 0.196062] 8018_l13: 1850 <–> 2950 mV at 2950 mV normal idle
[ 0.196490] 8018_l14: 2850 mV normal idle
[ 0.196825] 8018_lvs1: no parameters
[ 0.196917] 8018_lvs1: supplied by 8018_s3
[ 0.197314] vdd_dig_corner: 0 <–> 0 mV at 0 mV
[ 0.204578] ext_2p95v: no parameters
[ 0.204761] gpio_vreg_probe: id=18, name=ext_2p95v, gpio=18, gpio_label=ext_2p95_en
[ 0.205341] pm8018_probe: PMIC revision 1: F3
[ 0.205371] pm8018_probe: PMIC revision 2: 08
[ 0.205402] pm8018_probe: PMIC version: PM8018 rev 2.1
[ 0.205402] pm8018_probe: PMIC Restart Reason: Triggered by Hard Reset
[ 0.206867] pm_gpio_probe: OK: base=88, ngpio=6
[ 0.207416] pm8xxx_mpp_probe: OK: base=94, ngpio=6
[ 0.209552] msm_serial_hsl_probe: ttyHSL0 is disabled.
[ 0.209583] msm_serial_hsl: probe of msm_serial_hsl.0 failed with error -1
[ 0.210041] msm_serial_hsl_probe: ttyHSL1 is reserved for CONSOLE service.
[ 0.210071] msm_serial_hsl_probe: detected port #1 (ttyHSL1)
[ 0.210346] msm_serial_hsl.1: ttyHSL1 at MMIO 0x16440000 (irq = 186, base_baud = 460800) is a MSM
[ 0.210468] msm_hsl_console_setup: console setup on port #1
[ 0.314695] gpio_cf3_low_power_reset_timer_callback: LowPower_RESET pin toggled high
[ 0.314695] gpio_cf3_low_power_reset_timer_callback: LowPower_RESET pin toggle timer deleted
[ 0.847916] console [ttyHSL1] enabled
[ 0.863299] cpufreq_table_init: CPU: 4 scaling frequencies supported.
[ 0.869220] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0
[ 0.877735] hw-breakpoint: CPU 0 failed to disable vector catch
[ 0.884297] socinfo_init_dev: device_register fail (-22)
[ 0.891530] sps:REVISION of BAM 0xd0060000 is 0x5.
[ 0.895528] sps:BAM 0x12244000 is registered.
[ 0.899832] sps:sps is ready.[ 0.939386] bio: create slab at 0
[ 0.944269] ION heap vmalloc created
[ 0.946925] ION heap iommu created
[ 0.950221] ION heap audio created at 4ff01000 with size af000
[ 0.956752] pm8xxx_pwm_probe: OK
[ 0.959407] swimcu_i2c_init: start
[ 0.962673] swimcu_i2c_probe: start 1
[ 0.966274] swimcu_device_init: start 0x0
[ 0.970273] register_sierra_gpio_wake_notifier
[ 1.016633] swimcu_gpio_retrieve 0
[ 1.019258] swimcu_pm_sysfs_init: success func 1
[ 1.024172] swimcu_pm_sysfs_init: success func 2
[ 1.075537] swimcu_device_init: start 0x3f
[ 1.084510] swimcu_device_init: success
[ 1.101266] swimcu_set_fault_mask: 0x100, cnt 1
[ 1.104806] swimcu reset_recovery: complete
[ 1.108927] swimcu_set_reset_source: 0x40
[ 1.112925] swimcu_device_init: success
[ 1.116954] GPIOs are not in Slimbus mode
[ 1.120769] msm_slim_ctrl: probe of msm_slim_ctrl.1 failed with error -5
[ 1.128185] usbcore: registered new interface driver usbfs
[ 1.133007] usbcore: registered new interface driver hub
[ 1.138470] usbcore: registered new device driver usb
[ 1.144025] Advanced Linux Sound Architecture Driver Initialized.
[ 1.150495] NetLabel: Initializing
[ 1.152876] NetLabel: domain hash size = 128
[ 1.157210] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.162307] NetLabel: unlabeled traffic allowed by default
[ 1.168777] Switched to clocksource gp_timer
[ 1.235098] NET: Registered protocol family 2
[ 1.240470] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 1.246452] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 1.252830] TCP: Hash tables configured (established 2048 bind 2048)
[ 1.259209] TCP: reno registered
[ 1.262292] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 1.268121] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 1.429269] smem_find(9, 464): wrong size 912
[ 1.432595] get_nand_partitions: no flash partition table in shared memory
[ 1.439554] Notify: smsm init
[ 1.460338] NET: Registered protocol family 27
[ 1.465130] apr_tal:Q6 Is Up
[ 1.467663] apr_tal:Modem Is Up
[ 1.472516] modem_8960_init: modem fatal driver init’ed.
[ 1.477216] lpass_fatal_init: lpass SSR driver init’ed.
[ 1.482649] msm_rpm_log_probe: OK
[ 1.487623] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 1.682282] VFS: Disk quotas dquot_6.5.2
[ 1.685670] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.696535] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.703464] aufs 3.14-20140915
[ 1.705539] msgmni has been set to 293
[ 1.713169] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 1.719731] io scheduler noop registered
[ 1.723454] io scheduler deadline registered
[ 1.728124] io scheduler cfq registered (default)
[ 1.732702] wake-n_gpio wake-n_gpio: wake_n probe
[ 1.737372] gpio_check_and_wake: wake-n_gpio77 STATE=SLEEP
[ 1.886677] msm_serial: driver initialized
[ 1.890065] ttyHS0, function 1 is not valid on application processor.
[ 1.896200] msm_serial_hs: probe of msm_serial_hs.0 failed with error -1
[ 1.903067] msm_serial_hs module loaded
[ 1.918876] diag: In diag_smd_cntl_send_req, proc=0, Nothing to read from SMD
[ 1.926079] diagchar initialized now
[ 1.929467] diag: In diag_smd_cntl_send_req, proc=0, Nothing to read from SMD
[ 1.935785] diag: In diag_smd_cntl_send_req, proc=0, Nothing to read from SMD
[ 1.970090] diag: In diag_smd_cntl_send_req, proc=0, Nothing to read from SMD
[ 1.976255] diag: In diag_smd_cntl_send_req, proc=0, Nothing to read from SMD
[ 1.984007] brd: module loaded
[ 1.987974] wm8944 0-001a: revision A not fully supported
[ 1.992522] diag: Invalid Msg type 12 proc 2
[ 1.996459] wm8944 0-001a: WM8944 revision A
[ 2.002441] wm8944 0-001a: No interrupt specified, no interrupts
[ 2.008454] i2c-core: driver [tabla-i2c-core] using legacy suspend method
[ 2.014283] i2c-core: driver [tabla-i2c-core] using legacy resume method
[ 2.022066] msm_nand_init: Enabling failed write checking
[ 2.026583] msm_nand_probe: phys addr 0x1b400000
[ 2.031283] msm_nand_probe: dmac 0x3
[ 2.034762] msm_nand_probe: allocated dma buffer at d0065000, dma_addr 4f0b0000
[ 2.042026] flash_onfi_probe: No partition info available
[ 2.048008] status: c03020
[ 2.050083] nandid: 1590ac2c maker 2c device ac
[ 2.054570] Setting mtd->writebufsize to 0x800
[ 2.059056] Found a supported NAND device
[ 2.062994] NAND Controller ID : 0x4030
[ 2.066809] NAND Device ID : 0x1590ac2c
[ 2.070746] Buswidth : 8 Bits
[ 2.073676] Density : 512 MByte
[ 2.076880] Pagesize : 2048 Bytes
[ 2.080207] Erasesize: 131072 Bytes
[ 2.083656] Oobsize : 64 Bytes
[ 2.086769] CFG0 Init : 0xa8d408c0
[ 2.090279] CFG1 Init : 0x0004745c
[ 2.093728] ECCBUFCFG : 0x00000203
[ 2.097176] CW size : 528 bytes
[ 2.100595] BCH ECC : disabled
[ 2.103921] 7 cmdlinepart partitions found on MTD device msm_nand
[ 2.109964] Creating 7 MTD partitions on “msm_nand”:
[ 2.114909] 0x0000051c0000-0x0000052c0000 : “bootloader”
[ 2.123271] 0x0000052c0000-0x0000066c0000 : “kernel”
[ 2.144727] 0x0000066c0000-0x000009800000 : “rootfs”
[ 2.188982] 0x000009800000-0x00000bf80000 : “user0”
[ 2.225484] 0x00000bf80000-0x000014b00000 : “user1”
[ 2.340210] 0x000014b00000-0x000015000000 : “user2”
[ 2.350129] 0x000015000000-0x000015200000 : “user3”
[ 2.358736] spi_qsd spi_qsd.0: master is unqueued, this is deprecated
[ 2.364901] rmnet_init: BAM devices[8]
[ 2.378361] usbcore: registered new interface driver kaweth
[ 2.383000] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[ 2.390447] usbcore: registered new interface driver pegasus
[ 2.396062] usbcore: registered new interface driver rtl8150
[ 2.401770] usbcore: registered new interface driver asix
[ 2.407050] usbcore: registered new interface driver cdc_ether
[ 2.412910] usbcore: registered new interface driver dm9601
[ 2.418495] usbcore: registered new interface driver smsc75xx
[ 2.424233] usbcore: registered new interface driver smsc95xx
[ 2.429909] usbcore: registered new interface driver net1080
[ 2.435525] usbcore: registered new interface driver cdc_subset
[ 2.441477] usbcore: registered new interface driver zaurus
[ 2.447001] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[ 2.454509] usbcore: registered new interface driver int51x1
[ 2.460094] usbcore: registered new interface driver cdc_ncm
[ 2.465557] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 2.486006] msm_hsusb_host msm_hsusb_host: unable to find transceiver
[ 2.504593] platform msm_hsusb_host: Driver msm_hsusb_host requests probe deferral
[ 2.524523] msm_hsic_host msm_hsic_host: Qualcomm EHCI Host Controller using HSIC
[ 2.531176] msm_hsic_host msm_hsic_host: new USB bus registered, assigned bus number 1
[ 2.569327] msm_hsic_host msm_hsic_host: irq 264, io mem 0x12540000
[ 2.588860] msm_hsic_host msm_hsic_host: USB 2.0 started, EHCI 1.00
[ 2.596490] hub 1-0:1.0: USB hub found
[ 2.599420] hub 1-0:1.0: 1 port detected
[ 2.604974] usbcore: registered new interface driver cdc_acm
[ 2.609705] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.617915] usbcore: registered new interface driver usbserial
[ 2.623592] usbcore: registered new interface driver ftdi_sio
[ 2.629269] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 2.636654] usbcore: registered new interface driver option
[ 2.642118] usbserial: USB Serial support registered for GSM modem (1-port)
[ 2.649259] usbcore: registered new interface driver qcserial
[ 2.654723] usbserial: USB Serial support registered for Qualcomm USB modem
[ 2.661773] usbcore: registered new interface driver sierra
[ 2.667236] usbserial: USB Serial support registered for Sierra USB modem
[ 2.674042] usbcore: registered new interface driver GobiSerial
[ 2.679932] usbserial: USB Serial support registered for GobiSerial
[ 2.686189] usbcore: registered new interface driver usb_ehset_test
[ 2.692446] msm_otg msm_otg: msm_otg probe
[ 2.696444] msm_otg msm_otg: failed to get phy_clk
[ 2.701571] msm_otg msm_otg: OTG regs = d0070000
[ 2.708499] misc usb_link: registered misc device minor 47
[ 2.717106] mbim_init: initialize 1 instances
[ 2.720921] mbim_init: Initialized 1 ports
[ 2.730077] rndis_qc_init: initialize rndis QC instance
[ 2.735785] android_usb gadget: android_usb ready
[ 2.740943] input: pmic8xxx_pwrkey as /devices/platform/msm_ssbi.0/pm8018-core/pm8xxx-pwrkey/input/input0
[ 2.752083] rtc-pm8xxx rtc-pm8xxx: rtc core: registered pm8xxx_rtc as rtc0
[ 2.758217] i2c /dev entries driver
[ 2.763039] pm8xxx-adc supply pa_therm not found, using dummy regulator
[ 2.769052] swimcu_hwmon_probe: start
[ 2.772714] swimcu_hwmon_probe: success num 2
[ 2.801495] pm8xxx_tm_probe: OK
[ 2.804364] usbcore: registered new interface driver usbhid
[ 2.809217] usbhid: USB HID core driver
[ 2.814405] usbcore: registered new interface driver snd-usb-audio
[ 2.821730] voice_allocate_shared_memory: ION memory allocation failed
[ 2.827651] msm_pcm_probe: dev name msm-voip-dsp
[ 2.832443] msm_pcm_probe: dev name msm-host-pcm-voice
[ 2.838211] msm_pcm_probe: dev name msm-pcm-dsp
[ 2.842057] msm_pcm_probe: dev name msm-multi-ch-pcm-dsp
[ 2.848649] mdm9615_audio_init(): Interface Type (wm8944) = 1
[ 2.855150] mdm9615_audio_init - AR8, AR755xRD and CF3 configuration
[ 2.860857] soc-audio soc-audio.0: ASoC: machine mdm9615-wm8944-snd-card should use snd_soc_register_card()
[ 2.888142] soc-audio soc-audio.0: snd-soc-dummy-dai <-> MultiMedia1 mapping ok
[ 2.894948] soc-audio soc-audio.0: snd-soc-dummy-dai <-> MultiMedia2 mapping ok
[ 2.902151] soc-audio soc-audio.0: snd-soc-dummy-dai <-> CS-VOICE mapping ok
[ 2.909415] soc-audio soc-audio.0: snd-soc-dummy-dai <-> VoIP mapping ok
[ 2.915733] soc-audio soc-audio.0: msm-stub-rx <-> msm-dai-q6.241 mapping ok
[ 2.922813] soc-audio soc-audio.0: msm-stub-tx <-> msm-dai-q6.240 mapping ok
[ 2.929925] soc-audio soc-audio.0: snd-soc-dummy-dai <-> SLIMBUS0_HOSTLESS mapping ok
[ 2.937707] soc-audio soc-audio.0: snd-soc-dummy-dai <-> AUXPCM_HOSTLESS mapping ok
[ 2.945399] soc-audio soc-audio.0: snd-soc-dummy-dai <-> VoLTE mapping ok
[ 2.952144] soc-audio soc-audio.0: snd-soc-dummy-dai <-> DTMF_RX_HOSTLESS mapping ok
[ 2.959774] soc-audio soc-audio.0: msm-stub-tx <-> msm-dai-stub mapping ok
[ 2.966610] soc-audio soc-audio.0: msm-stub-tx <-> msm-dai-stub mapping ok
[ 2.973355] usb 1-1: new high-speed USB device number 2 using msm_hsic_host
[ 2.980466] soc-audio soc-audio.0: msm-stub-rx <-> msm-dai-stub mapping ok
[ 2.987273] soc-audio soc-audio.0: msm-stub-tx <-> msm-dai-stub mapping ok
[ 2.994445] soc-audio soc-audio.0: msm-stub-rx <-> msm-dai-stub mapping ok
[ 3.000946] soc-audio soc-audio.0: msm-stub-rx <-> msm-dai-q6.224 mapping ok
[ 3.007904] soc-audio soc-audio.0: msm-stub-tx <-> msm-dai-q6.225 mapping ok
[ 3.014985] soc-audio soc-audio.0: msm-stub-rx <-> msm-dai-q6.32773 mapping ok
[ 3.022401] soc-audio soc-audio.0: msm-stub-tx <-> msm-dai-q6.32772 mapping ok
[ 3.029665] soc-audio soc-audio.0: msm-stub-tx <-> msm-dai-q6.32771 mapping ok
[ 3.037936] hub 1-1:1.0: USB hub found
[ 3.040866] soc-audio soc-audio.0: msm-stub-rx <-> msm-dai-q6.2 mapping ok
[ 3.047764] soc-audio soc-audio.0: msm-stub-tx <-> msm-dai-q6.3 mapping ok
[ 3.054661] hub 1-1:1.0: 3 ports detected
[ 3.060033] soc-audio soc-audio.0: wm8944-hifi <-> msm-dai-q6.0 mapping ok
[ 3.066137] soc-audio soc-audio.0: wm8944-hifi <-> msm-dai-q6.1 mapping ok
[ 3.090096] TCP: cubic registered
[ 3.092385] NET: Registered protocol family 17
[ 3.097482] Registering SWP/SWPB emulation handler
[ 3.108499] clock_late_init() disabled 34 unused clocks
[ 3.115305] sps:BAM 0x124c2000 is registered.
[ 3.124462] no pmic restart interrupt specified
[ 3.128246] MSM Watchdog Initialized
[ 3.134716] ext_2p95v: disabling
[ 3.137036] regulator-dummy: disabling
[ 3.154555] msm_otg msm_otg: phy_reset: success
[ 3.160048] rtc-pm8xxx rtc-pm8xxx: setting system clock to 1970-01-01 00:24:03 UTC (1443)
[ 3.167221] ### dt-test ### No testcase data in device tree; not running tests
[ 3.186357] ALSA device list:
[ 3.190477] #0: mdm9615-wm8944-snd-card
[ 3.206683] Freeing unused kernel memory: 1368K (c08db000 - c0a31000)
mount root fs from partition (rootfs|system)
File /usr/bin/swi_auth does not exist or is not executable.[ 3.402868] msm_otg msm_otg: OTG state changed, charger_type NOT changed
[ 3.435251] ubi0: attaching mtd2
[ 3.439188] msm_otg msm_otg: OTG state changed, charger_type NOT changed
[ 3.539356] msm_hsusb_host msm_hsusb_host: Qualcomm On-Chip EHCI Host Controller
[ 3.545826] msm_hsusb_host msm_hsusb_host: new USB bus registered, assigned bus number 2
[ 3.578910] msm_hsusb_host msm_hsusb_host: irq 132, io mem 0x12500000
[ 3.609156] usb 1-1.1: new full-speed USB device number 3 using msm_hsic_host
[ 3.628841] msm_hsusb_host msm_hsusb_host: USB 2.0 started, EHCI 1.00
[ 3.638211] hub 2-0:1.0: USB hub found
[ 3.641568] hub 2-0:1.0: 1 port detected
[ 3.646940] msm_otg msm_otg: OTG state changed, charger_type NOT changed
[ 3.666534] ftdi_sio 1-1.1:1.0: FTDI USB Serial Device converter detected
[ 3.673035] usb 1-1.1: Detected FT-X
[ 3.676209] usb 1-1.1: Number of endpoints 2
[ 3.680238] usb 1-1.1: Endpoint 1 MaxPacketSize 64
[ 3.684938] usb 1-1.1: Endpoint 2 MaxPacketSize 64
[ 3.690035] usb 1-1.1: Setting MaxPacketSize 64
[ 3.695711] usb 1-1.1: FTDI USB Serial Device converter now attached to ttyUSB0
[ 3.799175] usb 1-1.3: new high-speed USB device number 4 using msm_hsic_host
[ 3.807904] random: nonblocking pool is initialized
[ 3.831374] hub 1-1.3:1.0: USB hub found
[ 3.834762] hub 1-1.3:1.0: 5 ports detected
[ 3.842179] ubi0: scanning is finished
[ 3.847276] msm_otg msm_otg: USB in low power mode
[ 3.857927] ubi0 warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 58, need 80
[ 3.869494] ubi0: attached mtd2 (name “rootfs”, size 49 MiB)
[ 3.874133] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.881062] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.887776] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.894735] ubi0: good PEBs: 394, bad PEBs: 0, corrupted PEBs: 0
[ 3.900717] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 3.907920] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1174495029
[ 3.917045] ubi0: available PEBs: 0, total reserved PEBs: 394, PEBs reserved for bad PEB handling: 58
[ 3.926262] ubi0: background thread “ubi_bgt0d” started, PID 76
UBI device number 0, total 394 LEBs (50028544 bytes, 47.7 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 3.964840] block ubiblock0_0: created from ubi0:0(rootfs)
DM verity is not enabled.
rootfs: dev ‘/dev/ubiblock0_0’ ‘squashfs’
rootfs: mounting took 10ms
[ 4.119853] usb 1-1.3.1: new high-speed USB device number 5 using msm_hsic_host
[ 4.189684] smsc95xx v1.0.4
[ 4.286555] smsc95xx 1-1.3.1:1.0 eth0: register ‘smsc95xx’ at usb-msm_hsic_host-1.3.1, smsc95xx USB 2.0 Ethernet, 36:f1:53:9f:85:b2
[ 5.667297] NET: Registered protocol family 1
init started: BusyBox v1.22.1 (2017-04-27 01:56:19 PDT)
rcS: Executing mount_essential_fs…
rcS: Executing simple_network…
rcS: Executing run_S_scripts…
S02mount_early: Executing mount_early_user_start…
S02mount_early: Trying to mount UBIFS on /mnt/flash using [usrquota,grpquota,rw] mount options…
[ 5.973386] ubi2: attaching mtd4
[ 6.721471] ubi2: scanning is finished
[ 6.724309] ubi2 error: ubi_read_volume_table: the layout volume was not found
[ 6.732305] ubi2 error: ubi_attach_mtd_dev: failed to attach mtd4, error -22
ubiattach: error!: cannot attach mtd4
error 22 (Invalid argument)
S02mount_early: Unable to attach mtd partition user1 to UBI logical device 2
S02mount_early: Trying to mount UBIFS on /mnt/flash using [rw] mount options…
[ 6.831222] ubi2: attaching mtd4
[ 7.579307] ubi2: scanning is finished
[ 7.582145] ubi2 error: ubi_read_volume_table: the layout volume was not found
[ 7.590141] ubi2 error: ubi_attach_mtd_dev: failed to attach mtd4, error -22
ubiattach: error!: cannot attach mtd4
error 22 (Invalid argument)
S02mount_early: Unable to attach mtd partition user1 to UBI logical device 2
[ 7.667633] yaffs: dev is 32505860 name is “mtdblock4” rw
[ 7.672485] yaffs: passed flags “tags-ecc-off”
S02mount_early: Executing mount_early_legato_start…
[ 8.171127] ubi1: attaching mtd3
[ 8.460949] ubi1: scanning is finished
[ 8.489058] ubi1: attached mtd3 (name “user0”, size 39 MiB)
[ 8.493605] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 8.517350] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 8.528002] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 8.534075] ubi1: good PEBs: 316, bad PEBs: 0, corrupted PEBs: 0
[ 8.540149] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 8.547138] ubi1: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1950926207
[ 8.556325] ubi1: available PEBs: 0, total reserved PEBs: 316, PEBs reserved for bad PEB handling: 80
[ 8.565542] ubi1: background thread “ubi_bgt1d” started, PID 177
UBI device number 1, total 316 LEBs (40124416 bytes, 38.3 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 8.610102] block ubiblock1_0: created from ubi1:0(legato)
S02mount_early: SQUASHFS successfully mounted on /mnt/legato
S02mount_early: Executing mount_early_userrw_start…
[ 8.740943] yaffs: dev is 32505861 name is “mtdblock5” rw
[ 8.745338] yaffs: passed flags “tags-ecc-off”
S03confighw.sh: Kernel internal entropy pool filler is available, increasing write_wakeup_threshold to 3072
S04mount_unionfs: RO rootfs will be fudged.
Loading modules: ftdi_sio sd_mod [ 9.273798] SCSI subsystem initialized
usb_storage [ 9.479505] usbcore: registered new interface driver usb-storage
msm_sdcc [ 9.564657] mmc0: mci-version: 18
[ 9.569571] mmc0: bam physical base=0x12182000
[ 9.573019] mmc0: bam virtual base=0xd01fc000
[ 9.577353] sps:BAM 0x12182000 is registered.
[ 9.598962] mmc0: BAM device registered. bam_handle=0xce6d2200[ 9.604150] sps:REVISION of BAM 0xd01fc000 is 0x5.
[ 9.612513] mmc0: Qualcomm MSM SDCC-BAM at 0x0000000012182000 irq 130
[ 9.617945] mmc0: Qualcomm MSM SDCC-DML at 0x0000000012180800
[ 9.623805] mmc0: No card detect facilities available
[ 9.633053] mmc0: Qualcomm MSM SDCC-core at 0x0000000012180000 irq 136,0 dma -1 dmacrcri -1
[ 9.649137] mmc0: 8 bit data mode disabled
[ 9.652220] mmc0: 4 bit data mode enabled
[ 9.667999] mmc0: polling status mode disabled
[ 9.683168] mmc0: MMC clock 400000 → 48000000 Hz, PCLK 0 Hz
[ 9.695437] mmc0: Slot eject status = 0
[ 9.708713] mmc0: Power save feature enable = 1
[ 9.722875] mmc0: SPS-BAM data transfer mode available
$Starting qcom_time:
starting time-daemon
Starting time_services: done
Mounting local filesystems…
Initializing random number generator…
[ 10.186021] sps:BAM 0x12502000 is registered.
[ 10.189867] enable_store: android_usb: already disabled
android0: Restoring ECM Host MAC ‘da:62:38:b3:d2:41’
[ 10.371432] Match for Function Name: diag, Int #0
[ 10.409552] Match for Function Name: nmea, Int #2
[ 10.413276] Match for Function Name: modem, Int #3
[ 10.418037] Match for Function Name: at, Int #4
[ 10.459026] Match for Function Name: rmnet0, Int #8
[ 10.462933] frmnet_bind: RmNet(0) dual Speed, IN:ep7in OUT:ep5out
[ 10.503738] ecm_native_function_bind_config: ecm_native_function_bind_config MAC: 00:00:00:00:00:00
[ 10.525377] android_usb gadget: using random self ethernet address
[ 10.539783] usb0: MAC e6:a9:af:6b:5e:c1
[ 10.542621] usb0: HOST MAC da:62:38:b3:d2:41
[ 10.546894] Match for Function Name: cdc_ethernet, Int #19
[ 10.579124] Match for Function Name: cdc_ethernet, Int #20
[ 10.620875] otg_pc = 3
Configuring network interfaces… [ 10.811139] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.947291] nf_conntrack version 0.5.0 (2372 buckets, 9488 max)
[ 11.209583] NET: Registered protocol family 10
[ 11.474072] ip6_tables: (C) 2000-2006 Netfilter Core Team
done.
Starting qti: done
Starting syslogd/klogd: done
[ 12.076392] smsc95xx 1-1.3.1:1.0 eth0: hardware isn’t capable of remote wakeup
Starting diagrebootapp: [ 12.099435] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
done
udhcpc (v1.22.1) started
Starting QCMAP_ConnectionManager: done
Sending discover…
[ 12.662353] nmea: smd opened
Starting qmuxd: done
Legato start sequence
Starting qmuxd…
Sending discover…
[ 16.859880] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1343c8, irq:187
[ 16.865557] qup_i2c qup_i2c.0: I2C slave addr:0x3a not connected
Finished Legato start Sequence
Starting netmgrd: done
Starting pm: done
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
starting DNS forwarder and DHCP server: dnsmasq… Sending discover…
done.
Starting Dropbear SSH server: DONE
dropbear.
Starting adbd: stopping DNS forwarder and DHCP server: dnsmasq… stopped /usr/bin/dnsmasq (pid 707)
done.
done
starting DNS forwarder and DHCP server: dnsmasq… Starting mbimd: done
[ 19.721532] adb_open
done.
Starting linkmon: [ 19.798473] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
done
run_getty.sh: ttyHSL1 reserved for CONSOLE
Poky (Yocto Project Reference Distro) 1.7.3 swi-mdm9x15 /dev/ttyHSL1
swi-mdm9x15 login: [ 20.226430] mbim_open: Open mbim driver
[ 20.240256] mbim_open: Lock mbim_dev->open_excl for open
[ 20.244559] mbim_open: USB cable not connected
[ 20.249565] mbim_open: Exit, mbim file opened
[ 20.257530] mbim_read: Requests list is empty. Wait.
[ 20.581748] gpio_sync_ri: RI owner is Modem
[ 20.584983] gpio_map_name_to_num: gpioRI is not supported
No lease, forking to background
Poky (Yocto Project Reference Distro) 1.7.3 swi-mdm9x15 /dev/ttyHSL1
swi-mdm9x15 login: root
Password:
Login incorrect
swi-mdm9x15 login: root
Password:
Linux swi-mdm9x15 3.14.29ltsi-13c67b16ff_922830eb31 #2 PREEMPT Fri Apr 15 02:38:16 PDT 2016 armv7l GNU/Linux
root@swi-mdm9x15:~# microcom –E /dev/ttyAT
BusyBox v1.22.1 (2017-04-27 01:56:19 PDT) multi-call binary.
Usage: microcom [-d DELAY] [-t TIMEOUT] [-s SPEED] [-X] [-E] TTY
root@swi-mdm9x15:~# microcom –E /dev/ttyAT
BusyBox v1.22.1 (2017-04-27 01:56:19 PDT) multi-call binary.
Usage: microcom [-d DELAY] [-t TIMEOUT] [-s SPEED] [-X] [-E] TTY
root@swi-mdm9x15:~# microcom -E /dev/ttyAT
AT
OK
at!UDINFO
ERROR
AT!ENTERCND=“A710”
OK
AT!UDINFO?
VID: 0x1199
PID: 0x68C0
Interface: QMI
Manufacturer: Sierra Wireless, Incorporated
Product: WP8548
OK
AT!USBCOMP
OK
ATI3
Manufacturer: Sierra Wireless, Incorporated
Model: WP8548
Revision: SWI9X15Y_07.12.09.00 r34123 CARMD-EV-FRMWR1 2017/04/26 23:34:19
IMEI: 359377060031167
IMEI SV: 45
FSN: LL621100050706
+GCAP: +CGSM,+DS,+ES
OK
ATI9
Manufacturer: Sierra Wireless, Incorporated
Model: WP8548
Revision: SWI9X15Y_07.12.09.00 r34123 CARMD-EV-FRMWR1 2017/04/26 23:34:19
IMEI: 359377060031167
IMEI SV: 45
FSN: LL621100050706
+GCAP: +CGSM,+DS,+ES
OK